Thu Mar 29, 2012 9:39 pm well maybe the two things are unrelated, I haven't run a 700 without a thermostat so I couldnt tell you on that...._________________PROUD Supporter ofMud and Mud-and-GutsAdminPosts : 5943Join date : 2009-07-15Age : 37Location : Celina, TennesseeSubject: Re: Rhino Fan Help Please! the way to check that is to put it into a small pot of hot water and slowly raise the heat then right when the water is about to boil the Connect the switch "earth" connection to the negative terminal of the battery (it will likely be well identified, green wire most likely).
No, create an account now. If you don't have one now would be a good time. I have added an additional ground cable from the motor to the frame and from the battery negative post to the frame.I did have my OEM ground pigtail burn up a Where should I go from here?... __________________ Jason 2012 Grizzly 700 w/EPS 27" ITP 589s on 14" MSA M15 Crushers 2" RDC lift 1.5" spacers on back, 1" on front EPI
Classifieds Store Advanced Search Forum Rhino Forums Yamaha Electrical radiator fan not coming on automatically, yet it will with override switch... Take a look:Here's the relayAnd above is a video to see what is happening. A few times, I the engine would not accelerate past 6500RPM even though I have a MSD.
They are a single beam meaning that whenever you have the switch on HI or LO, the lights have power. Number of bids and bid amounts may be slightly out of date. Iniciar sesión 11 1 ¿No te gusta este vídeo? Here is a video I made showing the problem and the exact relay I replaced.
The time now is 11:38 PM. -- Rhino v2 -- .Mobile Style. - Contact Us - Advertise - Yamaha Rhino Forum - Rhino Forums.net - Yamaha ATV Forum - Archive - Grizzly 660 Fan Relay Location haha!Ok, maybe I spoke too soon. My problem has manifested itself in a new way. LIFE IS FULL OF MUD ... http://www.grizzlycentral.com/forum/grizzly-engine-transmission/10330-2007-660-fan-just-stopped-working-overheating-now.html Thu Mar 15, 2012 5:09 pm ok i dont know if the 700s are different or i just aint looking for the right thing..but mine dont have any kind of switch
the fan on the radiator stopped, it is freed up and will run when hooked to a power source. The OEM meter was showing, at first, a volt or two lower than my Autometer gauge. Note that passwords are case-sensitive. Thanks __________________ 97 Warrior K&N, dynojet,DMC alien exhaust, renthal handlebars, renthal 14t sprocket. 03 Raptor 660 K&N pro-flow, FMF, Duncan, Renthal, MSR, IMS 03-13-2007, 11:30 PM #16 phucker Primo
ETA: I noticed that the switch will take a few seconds to light up when over 160deg. LIFE IS FULL OF MUD ... Yamaha Rhino 700 Fan Relay Cola de reproducciónColaCola de reproducciónCola Eliminar todoDesconectar Cargando... Yamaha Kodiak 400 Fan Not Working I know yamaha had a problem where some would only run for 30 seconds on and off but mine works fine.
DynatekElectronics 17.769 visualizaciones 3:07 700 rhino e-brake mod - Duración: 1:26. Just don't know where to start... What in the world?!?The headlight HI/LO relay is good, and it clicks normally when you switch to high beams. Dont know if it is the thermo switch in the radiator or the circuit breaker.
Cargando... ruyguy8888 9.351 visualizaciones 1:33 rhino 660 head studs.AVI - Duración: 6:30. Fredrico Suave 9.782 visualizaciones 1:57 Cargando más sugerencias... Im not the electrical guru around here and Steve knows the wiring colors far better than i do. 2006 Rhino 660 686 Big bore, 11:1 comp, stage 1 cam Elka stage
Sun Sep 15, 2013 5:02 pm Mine is also grounded to the battery,working fine foe now but I still have added a heavier ground frame to engine and a large stud could your quad battery be weak? It has 2 wires running into it.
seminaryranger 5.582 visualizaciones 2:34 JBS Teryx Clutch - Belt Info - Duración: 4:57. I believe that you can probably find a 40A rated relay that will fit there.You certainly have me stumped on this one. I'm not certain but I think you can still start the engine and drive. Email Address: OR Log-in User Name Password Remember Me?
Ran wire to switch which is grounded so light comes on when power is passing thru the switch. start the motor take wires off temp sending unit put a jumpr wire between them. I swapped the SPDT in place, temporarily to verify the relay was [one of the] bad part(s). What is happening is that the relay fails in a strange way. Vuelve a intentarlo más tarde.
I see a lot of feathers but not much chicken !!!!!!!! I have to get this fan running again... __________________ Jason 2012 Grizzly 700 w/EPS 27" ITP 589s on 14" MSA M15 Crushers 2" RDC lift 1.5" spacers on back, 1" on My aftermarket accessories all functioned properly. Añadir a Cargando listas de reproducción...
kjackLite MudderPosts : 53Join date : 2011-04-14Age : 29Location : Crossville,TnSubject: Re: Rhino Fan Help Please! Transcripción La transcripción interactiva no se ha podido cargar. Last Jump to page: Quick Navigation Yamaha Electrical Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Main Category Welcome to Hot Rod Forums Member Introductions Wed Mar 21, 2012 10:06 am yes when it did overheat the water was gurgling and coming out the overflow in the dash.hasnt got hot enough to do it again though.maybe
I hope that the wrapped pipe and the fan not running is just coincidental, and not a cause and effect...I don't see why it would be. When my Rhino was new, before I ever rode it, I greased all the electrical connectors. Stay logged in UTVUnderground.Com - The #1 Resource for SXS Enthusiasts Home Forums > UTVUnderground 'Shop Talk' > UTV Engines, Performance, Maintenance > Certain XenForo add-ons by Waindigo™ ©2011-2012 Waindigo Limited. Got a very weak turn out of the fan, and sometimes wouldn't turn at all.
WVHotRodRhino 239 visualizaciones 4:57 JBS Kawasaki Teryx Gear Ratio Explanation - Duración: 5:25.