zenlinux.org

Home > Not Working > Dashboard Gauges In Car Not Working

Dashboard Gauges In Car Not Working

Contents

To begin the first 5 tests, press the U.S./MET button. I reviewed the bulletin for the special care, however my Burb has too much mileage to qualify. Connect the meter to the sensor terminals and turn it. Upvote (56)Flag inappropriate2004 Chevrolet Silverado 2500 HD 50,000 mi, CoolD2Here are a couple of inexpensive possible solutions. http://zenlinux.org/not-working/gauges-not-working-on-dashboard.html

So I bought a 25watt iron and kit with removable tips (about $17 at HD). Ground point failure? DEALERS ARE TO OBTAIN THE VEHICLE MILEAGE WHEN SCHEDULING A SERVICE APPOINTMENT. Now the fuse 21 keeps blowing when you turn on ignition, but the truck still starts and runs there is no power windows, interior lights, radio, nothing works on the cluster. http://ezautoremote.com/2013/05/instrument-cluster-what-to-do-when-they-dont-work/

Dashboard Gauges In Car Not Working

Turns out it seems to be for a trailer turn signal contact when towing something (according to the wiring diagram). The issue now is when any of the doors are open and the dome switch is on the fuse # 21 will blow and lose every thing again, if the dome This may cause inaccurate readings, including the speedometer and fuel gauge. Be warned, however, that rolling back the mileage to make your vehicle appear to have less wear and tear than it actually has can get you into hot water if you

Reply July 21, 2014 at 10:28 pm Stuart Gross I would have a more qualified technician look at the car…. The trick here is to hold the plastic circuit board firmly in place with your fingers while using the eraser so as not to wrinkle or crease the plastic. He did not want to spend that amount of money and traded the car for a new one. My Instrument Panel Is Not Working Reply With Quote 06-07-2011,03:34 PM #14 Uzzy Firebird Concept (the turbine one) Join Date Jan 2005 Location Windsor Ontario, Canada Posts 11,214 Garage Bonnie Thanks 10 Thanked 3 Times in

But not always. The odometer should display EIC indicating the cluster is ready to begin the self tests. Thank you, Stu Reply October 23, 2014 at 1:49 am Jaxon My headlights, tail lights, cluster lights wont come on.. I disconnected my battery as recommended.

Thank you, Stu Reply October 18, 2014 at 6:14 pm Julio G Hello , I have a 2000 pontiac sunfire and I recently had a speedometer failure , I googled it Gauges Not Working On Dashboard Once you have the front cover off, you can inspect the innards of the cluster for anything that might look out of place - of course, since I don't know what For vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after September 28, 2007 for 2003-2004 model year vehicles, and March 23, 2009 for 2005 model It did always came on, eventually.

Instrument Cluster Not Working Chevy Silverado

The repairs will be made at no charge to the customer. Discover More Back and forth intermittently. Dashboard Gauges In Car Not Working No power windows Everton else seem good The electric brakes work good Now what I'll have a look around . 1 out of 1 people think this is helpful. Dashboard Gauges Stopped Working November 15, 2014 at 5:18 pm Stuart Gross most likely the sending unit in the tank… have it checked by a professional.

After running for 10-15 minutes, I can turn off the vehicle, pull the key, open/close the door and restart. navigate here Thanks, Stu Reply November 15, 2014 at 4:48 pm Rita I have a 1998 Chrysler Sebring Convertible, the temperature gauge on the dash stops working,but everything else is still working. Thank you, Stu Reply June 11, 2014 at 7:38 pm Sharon About 5 years ago, my gas gauge started acting up on my 2002 Pontiac Montana van. Either the headlamp switch has gone bad and will need to be replaced or the interior lightÂ’s dimmer switch is turned down. Instrument Cluster Fuse 2004 Chevy Silverado

Lost all gauges on dash,raido works. Frustrated!! These inputs typically come from a variety of vehicle sensors, all of which can go bad. http://zenlinux.org/not-working/my-dashboard-gauges-stopped-working.html Pull the dimmer switch and the cluster backing lights that illuminate in the night don't turn on.

It can all easily fit on an 8.5" X 11" sheet of paper. Instrument Cluster Lights Not Working Reply August 3, 2014 at 1:56 pm Stuart Gross Hi, Check all the grounds… then have a mechanic look at the wiring harness connections. I don't know all the details / models involved, but perhaps one of our dealer members will chime in.

all other gauges work fine..

And my gaues go on and off ehile driveing. First, put the fuel/temp gauge back in place and re-attach the front cover of the instrument cluster - check for any debris that may have fallen into the front cover before Reply November 25, 2014 at 3:08 pm Stuart Gross You have serious issues. Bad Instrument Cluster Symptoms Here's where the right-hand instruments are located looking at the back side.

In early September 2010 the instrument cluster (speedometer, tachometer, temperature gauge, fuel gauge, and various warning lights) stopped lighting up and registering ... 1 Step 1: Eliminate other possible causesA worn A 10 Amp. I switched out the bulbs out and still, only the one side is working. this contact form Thank you, Stu Leave Comment Cancel reply Your email address will not be published.

vehicles, dealers are to provide the customer with an instrument panel cluster (IPC) only. All vacuum fluorescent displays should illuminate. If the speedometer and odometer do not work, check the operation of the "distance sensor" (speedometer sending unit) on the transaxle with an ohm meter. First, check all connections to be sure that your colors and wire functions are mating with each other (green to green, blue to blue, etc,) and check for good crimps.

Are you local to me? After checking all the indicator/warning bulbs, I found I had one that was burnt out and another that was very dim - So I ordered a couple of replacements from 928 Loading... Unforntunately, I can't read german (except I noticed one word - looked like blinker).

Category Autos & Vehicles License Standard YouTube License Show more Show less Loading... Check voltage at the working bulbs then at the dead bulbs Reply September 8, 2014 at 11:26 pm Stuart Gross Have it checked by a mechanic ASAP. Is this an instrument cluster problem or am I in deep trouble. Checked and cleaned all relays, replaces suspicious looking fuses, and tested all fuses.

Removed cluster, it appeared the two small gauge lights were blown. Without a ground, the gauge will not register. As it appears there's a choice of potentials for the fault, an instrument cluster panel, ignition switch, ground point or BCM Reply With Quote 10-21-2010,10:53 AM #6 sonjaab 6.2 Liter LS3 Better get it checked quickly.

Use the probe on the other lead to touch the small metallic spots on the top surface of the fuse. LCD not Stuck or fluttering needles on gauges Burned out indicator lights Burned out/dark spot backlighting Loss of LCD display or erratic operation (number 8 showing as 0) Instrument Cluster - How